JLT COLD AIR INTAKE KIT (2003,2004 MACH I)

Description

JLT Next Generation Cold Air Intake system for the 2003 & 2004 MACH I available in black textured plastic,painted body color or HydroCarbon finish.
This replaced our original Cold Air Intake kit in January 2012.

INTAKE TUBE
Using the original JLT CAI as a guide, we molded, sculpted and perfected everything until we had the best looking, fitting and performing system you can buy.
The JLT tube is 4 1/4″ ID, roto molded plastic to resist engine heat and keep the intake air charge nice and cool. NO METAL TUBING HERE!!

MAF and filter relocated into fender well for a cooler intake charge and can support up to 550 RWHP.

Works with both 80mm and 90mm MAF’s, no need to buy more parts if you upgrade to a 90mm MAF.

MOLDED IN MAF
The best part of this new JLT Cold Air is we kicked the cool factor up a notch and molded a 105mm MAF housing right in the tube. Now you have a kit you can grow into and not have to buy a complete new kit when you reach over 550 RWHP. Putting a Whipple, Kenne Bell or Eaton blower swap on your MACH? Simply drill out the pre molded plug on the MAF block located on the bottom of the tube, discreetly out of sight. Install your SCT MAF sensor electronics, add our huge 4.5 X 12” S&B Powerstack filter and you’ve now changed your JLT Cold Air Intake into a JLT High Boost 12” Intake. Molding the MAF into the tube makes for a much smoother air flow with no couplers, reducers or separate MAF housing and can support 800+RWHP for only the cost of the 12” upgrade kit, $60.00.

GAINS
14-16 RWHP are typical with this kit.

FINISH OPTIONS
Standard finish is an OEM looking black textured plastic and also available in your cars exact body color. All painted tubes receive a special treatment so paint adheres correctly to the plastic and go through an in-depth process to remove all the texture. We then use only the best quality materials to give each tube a smooth gloss finish.

Now also available in HydroCarbon
Through an awesome process called Hydrographics, the intake tube is made to look like carbon fiber. The tube is painted and then dipped in a water solution with a carbon fiber print film that adheres to the part when removed. Tube is then clear coated for a durable finish. See picture of intake tube below and HydroCarbon option in the Intake Tube Options.

EASY INSTALL
The new design, detailed instructions and online video instructions helps make this an easy install.
Install Instructions

KIT INCLUDES:
•JLT Plastic Intake Tube
•Rubber Elbow
•Silicone Reducer
•Apron Plate
•4×6 S&B Powerstack Air Filter
•Silicone MAF Spacer
•MAF Adapter
•MAF Adapter Gasket
•HD Clamps & all needed hardware

Stock Shaker system is NOT used with this kit.
Will not fit with most strut tower braces.

MAINTENANCE
To properly clean your oil filter, we recommend the S&B Precision II Cleaning & Oiling Kit.
*TIP* by purchasing a 2nd air filter you can simply swap filters when it’s time to clean it and not be rushed. Clean the first filter and it’s ready when it’s time to change again.

*The air filter is low in the bumper to get the coolest air possible. While driving in the rain is not an issue, you MUST be aware of flooded streets and deep puddles. *

JLT Pre-Filters are now available for most intake kits we carry, these filters are made for us by Outerwears, these prefilters are water repellent. They will increase your filter life and cut down on your cleaning intervals! For more information check the product page here JLT Air Filter PRE FILTER

This kit is street legal in all US states.
CARB Exempt ID: D-761

Additional information